Dacor ER36D-C Specifications download pdf (Page 6)

Planning the Installation

WARNING

IMPORTANT: Observe all governing codes and ordinances

during planning and installation. Contact your local building

department for further information.

Electrical Requirements

IMPORTANT: The information below does not apply to units

equipped for use in Canada.

It is the owner’s responsibility to ensure that the electrical

connection of this appliance is performed by a licensed electrician.

The electrical installation, including minimum supply wire size

and grounding, must be in accordance with the National Electric

Code ANSI/NFPA 70-1993 (or latest revision) and local codes and

ordinances. The standard is available from:

National Fire Protection Association

1 Batterymarch Park

Quincy, Massachusetts 02269-9101

• The correct voltage, frequency and amperage must be

supplied to the appliance from a separate, grounded, circuit

that is protected by a properly sized circuit breaker or time

delay fuse. If a fuse is utilized, fuse both sides of the line (L1

and L2).

NOMINAL ELECTRIC CIRCUIT REQUIREMENTS - U.S.A.

Range

Model

Circuit Required

Total Connected

Load

ER36D

240 Vac*, 60 Hz, 30 Amp. (Min.)

40 Amp. (Recommended)

6.5 kW (28 Amp.)

ER48D 240 Vac*, 60 Hz, 50 Amp. 10.0 kW (42 Amp.)

* 4-wire, two 120 Vac hot (L1 and L2), one neutral, one ground

The ratings above are for reference only. Refer to the range rating

label for exact specifications (see page 3 for location).

• Consult local building codes for the type and minimum wire

gauge to use for the power requirements listed on the rating

label.

• Suggested wiring color code: Black, white, red and green.

• The wiring needs to be long enough to allow the range

to be pulled out from the wall for service, while remaining

connected. See page 8 for further details.

• The wiring to the range must:

◊ Have a minimum rating of 250 Volts @ 30 Amps for

model ER36D, 250 Volts @ 50 amps for model ER48D

◊ Include a strain relief

◊ Be terminated by tinned leads, closed loop terminals or

open ended spade lugs with upturned ends

• Where local code permits, a three (3) or four (4) wire

appliance cord may be used. The appliance cord must:

◊ Be UL listed type SRD or SRDT

◊ Be equipped with a NEMA 14-50P 4 wire plug or, where

local code permits, a NEMA 10-50P 3 wire plug.

• Prior to range installation, have a licensed electrician install a

conduit junction box or electrical receptacle according to the

type of wiring used.

Electrical Requirements - Canada

It is the owner’s responsibility to ensure that the required 4 wire

electrical outlet is installed by a licensed electrician as specified

below prior to range installation. The electrical outlet installation,

including minimum supply wire size and grounding, must be in

accordance with all governing codes and ordinances.

• The correct voltage, frequency and amperage must be

supplied to the appliance from a separate, grounded, circuit

that is protected by a properly sized circuit breaker or time

delay fuse. If a fuse is utilized, fuse both sides of the line (L1

and L2). Refer to the data on the range rating label.

NOMINAL ELECTRIC CIRCUIT REQUIREMENTS - CANADA

Range

Model

Circuit Required

Total Connected

Load

ER36D

240 Vac*, 60 Hz, 30 Amp. (min.)

40 Amp. (Recommended)

6.5 kW (28 Amp.)

ER48D 240 Vac*, 60 Hz, 50 Amp. 10.0 kW (42 Amp.)

* 4-wire, two 120 Vac hot (L1 and L2), one neutral, one ground

The ratings above are for reference only. Refer to the range rating

label for exact specifications (see page 3 for location).

• Freestanding ranges equipped

for use in Canada come pre-

wired with a 4 wire appliance

cord and NEMA 14-50P plug.

• Do not modify the factory wiring.

The plug is designed to plug

directly into a NEMA 14-50R

electrical receptacle installed by

a licensed electrician according

to the above specifications.

Gas Supply Requirements

• Check your local building codes for the proper method of

installation. In the absence of local codes, this appliance

should be installed in accordance with the National Fuel Gas

Code ANSI Z223.1.

• Be certain that the appliance being installed is correct for

the gas service provided (natural gas or LP gas). Also, if

operating the range at an altitude above 4000 ft. (1219 m)

make sure it is equipped for high altitude operation. Refer

to the range rating label and the table on page 3 to

determine the correct model.

• See the table below for gas supply pressure requirements.

• The regulator inlet accommodates a 3/4” gas line. The range

ships with a 1/2” to 3/4” adapter connected to the regulator.

GAS SUPPLY PRESSURE REQUIREMENTS*

Gas Type

Minimum

Manifold Pressure

Minimum Gas

Supply Pressure**

Natural Gas 5” Water Column 6” Water Column

Liquid Propane (LP) 10” Water Column 11” Water Column

* The gas supply pressure for testing the regulator setting shall

be at least 1 inch water column (249 Pa) above the specified

manifold pressure.

** Maximum gas supply pressure for all models: 1/2 psi.

The ratings above are for reference only. Refer to the range rating

label for exact specifications (see page 3 for location).

NEMA 10-50P PlugNEMA 14-50P Plug

NEMA 14-50R Receptacle

(All units)

1 2 3 4 5 6 7 8 9 10 11 ... 19 20

Comments to this Manuals

No comments

Dacor ER36D-C Specifications Page 6

Comments to this Manuals

Related products and manuals for Cookers Dacor ER36D-C