Dacor DRF427500AP Installation Manual download pdf

Uncrating the refrigerator

Ƹ͝ϑʀθʪиϩ˵ʪɵͱ̷ϩϑ

đՑуՌՋ׋ՌՋʪɇ

• Remove the brackets from the pallet by

unscrewing the bolts (ve per bracket).

Attaching the anti-tip bracket

Cabinet

Height



đՏуՎՐ׋Ցʪɇ

Wooden Wall

󰞊

Concrete wall

đՏуՎՐ׋Ցʪɇ

ØՑуՎՋ׋Ցʪɇ

󰞊

󰞒

ՍٓطՐՋظ

ƊΧɇʀʪθطиͱͱʒظ

ΧΧ̷̈ɇ͝ʀʪ ΧΧ̷̈ɇ͝ʀʪ

󰞅

• Bracket height is measured from the oor

and depends on the cabinet height.

• Attach the anti-tip brackets. Ensure the

screws hold the bracket tightly.

• The anti-tip brackets must extend at least

2” (50 mm) over the appliance to secure the

appliance. If this minimum length cannot

be observed for structural conditions

it is possible to do this by fastening a

spacer(wood) behind the anti-tip angle.

* Bracket height = Cabinet height – 4 3/32” (104 mm)

Cabinet height A

Case 1 83 1/2” (2121 mm) 79 1/2” (2019 mm)

Case 2 84” (2134 mm) 79 7/8” (2030 mm)

Cabinet special requirements

10”

(254)

Electric supply

location

6”

(154)

ø1/4”(6.5)

1”

(25.4)

Water supply

location

A : Cabinet Width

B : Cabinet Depth

C : Cabinet Height

D : Electrical supply width location

E : Electrical supply height location

F : Water supply outlet location

*B : Includes the standard door panel

thickness with 1/4”

* Installation insidea cabinet of

this width allows the refrigerator

trim to be attached directly to the

surrounding cabinets.

• Connect refrigerator power cord plug to a

properly earthed receptacle. Set the Master

Power Switch to the “I” (ON) position.

• Check to make sure power to refrigerator

is on by opening refrigerator door to see if

interior lights are on.

42”

A 42” (1067mm) D 22” (559mm)

B 25” (635mm) E 80” (2032mm)

C 84” (2134mm) F 12” (305mm)

Moving the refrigerator into its enclosure

ĮЭʪθ̷ɇцƟцΧʪ

Aɇɵ̈

Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ

ƟͱΧӬʪи

θɇ͔ʪ̷ʪϑϑƟцΧʪ

Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ

Aɇɵ̈

â̈˝

طťͱϑ̈ϩ̈ͱ̈͝͝˝ɇ̈ʒظ

ĮЭʪθ̷ɇц

θɇ͔ʪ̷ʪϑϑ

󰞓

ťɇ͝ʪ̷

θʪɇʒц

ťɇ͝ʪ̷

θʪɇʒц

ťɇ͝ʪ̷

θʪɇʒц

ťɇ͝ʪ̷

θʪɇʒц

Ռժٗٗ

طՏՋ͔͔ظ

Ռժٗٗ

طՏՋ͔͔ظ

• According to the type of cabinet, a jig

(positioning aid) can be used to align the

refrigerator’s custom door panel with cabinet

by marking vertical line on the cabinet.

• Position the cabinet side chassis to align with

your vertical line.

Leveling the refrigerator

θͱ͝ϩ

ʒ̟Їϑϩɇɵ̷ʪϑ˵ɇ˙ϩ

طՎ؏Փٓ׋ՌՋ͔͔ظ

đɇу

ՍՋ͔͔

âɇʀ̧ϩцΧʪط˵ʪ̈˝˵ϩɇʒ̟Їϑϩ͔ʪ͝ϩظ

ŵʪɇθ

• Attach the refrigerator’s top cover and trim

top cover to the hook at the top front of the

chassis.

• Using your drill and the bit shown below,

engage each of the refrigerator’s adjuster

shafts in turn, and level the refrigerator.

( CW ↑, CCW ↓)

Adjust the gap between the furniture and

upper chassis cover to 1/8 in. (3mm ).

• The front and rear leveling legs have a

maximum height adjustment of 3/4 in.

(20mm).

Installation guide

Securing the refrigerator

̈уʪʒ̷ͱʀɇϩ̈ͱ͝

ƟͱΧǤ̈ʪи

󰞊

ťɇ͝ʪ̷θʪɇʒц Aɇɵ̈

Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ

طƟ²ظđՏуՌՏ׋ՌՍʪɇ

• Remove freezer box.

• Secure the refrigerator to its enclosure with

(TH) M4 x 14 screws (6 screws per side, as

shown in the graphic).

Attaching the Cabinet Trim

A˵ɇϑϑ̈ϑϑΧɇʀʪθ

Aɇɵ̈͝ʪϩϑ̈ʒʪϩθ͔̈

• Attach the trim between the refrigerator and

the cabinet.

Attaching the Custom-Door-Panel Brackets

Ƹťť׊Րʪɇ؏øĮǮ׊Րʪɇ

󰞈

θ̈ʒ˝ʪUͱͱθøͱи

ط²ظđՏуՌՏ׋ՌՋʪɇ

Ƹťť׊Տʪɇ؏øĮǮ׊Րʪɇ

󰞈

ط²ظđՏуՌՏ׋Քʪɇ

θ̈ʒ˝ʪUͱͱθƸΧ

θʪʪіʪθUͱͱθƸΧ

θʪʪіʪθUͱͱθøͱи

Custom Panel: STS

• Drive screws each to the top and bottom

brackets as shown in the graphic.

(The other holes on each side of the bracket

are for a different application.)

Ƹť

øĮǮ

Panel

Template

REFFRE

ط²ظđՏуՌՏ׋ՌՋʪɇ

Ƹťť׊Րʪɇ؏øĮǮ׊Րʪɇ

󰞈

Custom Panel: Wood, Other

• The template informs you the position of the

bracket and holes.

• Mark hole positions on every corner of the

panel according to the template and drive

the screws into the holes.

Aligning the panel (Order : Top → Side →

Front/Back)

UͱЇɵ̷ʪϩ˵θʪɇʒʪʒ

ɵͱ̷ϩ

Ɗ̈ʒʪϑʀθʪи

Ęͱ׵Սϑʀθʪи

Ęͱ׵Ռϑʀθʪи

đՑуՌՍ׋ՌՌʪɇ

kɇʀ˵ՌՌϑʀθʪиϑΧʪθUͱͱθ

󰞈

ťɇ͝ʪ̷Χͱϑ̈ϩ̈ͱ͝ɇʒ̟Їϑϩʪθ

󰞇

đՌՎ

• There are two panel-adjustment mechanisms

at the top and two at the bottom of the door.

• A side screw to shift the panel side to side;

Screw 1 to shift the panel backward

Screw 2 to shift the panel forward

• To attach the Panel to the Door, screw nuts

snugly onto the double-threaded bolts.

(2 nuts per door)

DA68-03686A-00

CAUTION

Please read the installation insturctions carefully before you install the product.

No NAME Q'TY

1 PANEL BRACKET L-UP, R-LOW 4

2 PANEL BRACKET R-UP, L-LOW 4

3 ANTI-TIP BRACKET 2

4 NUT-HEXAGON FLANGE 8

5 BOLT-HEX 44

6 SCREW-TAPPING 40

7 SCREW-TAPPING 12

8 SCREW-TAPPING 6

9 TOP TABLE 1

10 LOWER DOOR CAP REF LEFT 1

11 LOWER DOOR CAP REF RIGHT 1

12 UPPER DOOR CAP FRE LEFT 1

13 UPPER DOOR CAP FRE RIGHT 1

14 TRIM TOP COVER 1

15 GAP GUIDE 1

16 HOLDER LOCK 6

17 BRACKET TEMPLATE-REF 1

18 BRACKET TEMPLATE-FRE 1

19 INSTALLATION GUIDE 1

     

M13 M6 x 12 (FH) M4 X 14

     

(TH) M4 X 16 M4 x 35

     



T-Type

1 2

Summary of Contents

Page 1 - Installation guide

01 Uncrating the refrigeratorƸ͝ϑʀθʪиϩ˵ʪɵͱ̷ϩϑđՑуՌՋ׋ՌՋʪɇ• Remove the brackets from the pallet by unscrewing the bolts (ve per bracket).02 Attachin

Page 2 - Guide d’installation

Guide d’installationFR01 Déballage du réfrigérateurUʪϑϑʪθθʪі̷ʪϑɵͱЇ̷ͱ͝ϑđՑуՌՋ׋ՌՋΧ̈ʽʀʪϑ• Retirez les deux xations de la palette en dévissant les bo

Comments to this Manuals

No comments

Dacor DRF427500AP Installation Manual

Browse online or download Installation Manual for Unknown Dacor DRF427500AP. Dacor DRF427500AP Installation Manual User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Dacor DRF427500AP